A good way to get rid of any oily residue or any dirt is to use a really fine piece of sandpaper or even an emery cloth. Another thing that you can consider using is some rubbing alcohol. This is quite effective. After you have inspected this and made sure that everything is ok, you will then need to make sure that the wires are connected with solder.
After you install the motor, replace back the pinion gear and then put back on the drive gear cover and you are almost there! First thing you need to do is to locate the old ESC in your vehicle. The ESC may be fitted in a couple of ways:. Whatever it is, remove the ESC gently and carefully. Once you have done this you then need to install the new ESC. Make a decision if you want to fasten it to the vehicle using mounting screws, if this is a possibility, or if you would prefer to secure it in place with double-sided foam tape.
Once you have attached it to the vehicle, take the two battery connectors and plug them into a fully charged power pack in the vehicle. You then need to take the third lead and connect this to the receiver. Once you are happy that it is secure and connected you will then need to Bench teste it, to make sure that it is functioning correctly. Once everything is connected, the cover is back on and everything is up and running.
You will need to verify it is running ok. Turn on the vehicle and the transmitter. Try to operate it in the normal way. Nine times out of ten it is likely to be a loose connection that you have missed in the vehicle.
Or, something has not been put back correctly. If this happens, just double check all the wiring and make sure everything is secure. One last tip. Always make sure that the transmitter batteries are fully charged. This may sound simple, but you may think that something is wrong with the car and it could literally just be the batteries need more power. Do I actually need a new ESC for a brushless motor? Yes, you do need a brushless ESC for the brushless motor.
You actually need to make sure that you have the right amp level for the type of ESC that you have for your vehicle. What is a brushed ESC? For returned merchandise that is found to be genuinely defective, we ship out replacement for free we pay for the replacement shipping cost and will not charge additional shipping and handling fees.
We reserves the right to return merchandise to its customer and not refund money, if we in our opinion deem that the merchandise has been used, crashed, abused, misused or modified in any form, or has been damaged by water, dust, or other contaminants. Please also check over the product especially the helicopters and air planes and make sure they are all good every time before use or taking to the air.
Please understand that RC helicopters and airplanes can crash if mistake made or you do not know how to fly, any kind of crash or hard landing may caused damage s to the helicopter or plane.
We have no control over your flying skill, behavior or the conditions you have chosen to fly in. We tested all products before shipment as we stated above, if you have any problem with the aircraft or other product s you ordered from us, please report it at the time when you received the shipment not after use please.
We are sorry but we can not be responsible for your crash or use. Remote controlled products and accessories can be very dangerous. Please read the operating manual before use. We have no control over the correct use, installation, application, or maintenance of our products, no liability shall be assumed nor accepted for any damages, losses or costs resulting from the use of the products. Any claims arising from the operating, failure or malfunctioning etc. We assume no liability for personal injuries, property damages or consequential damages resulting from our products.
If you do not agree to our terms, please do not make the order. We reserves the right to amend this policy without further notification s. Facebook Weekly Giveaway. Thunder Charger. Get notified when product is back in stock:. How to Use: The connection of the brushless converter is straight-forward. Get The Latest. Sometimes people just forget about posts if they end up figuring it out so I thought if I posted in his thread, he might respond.
I am simply looking for a way to use an arduino or any microcontroller for that matter to convert the duty cycle and polarity output of a 8. So one end is connected to the brushed ESC like the motor would be and the other end outputs a servo signal for a brushless esc to plug into. TechnoPsycho to convert the duty cycle and polarity output of a 8.
TechnoPsycho I am simply looking for a way to use an arduino or any microcontroller for that matter to convert the duty cycle and polarity output of a 8. So one end is connected to the brushed ESC like the motor would be, and the other end outputs a servo signal for a brushless esc to plug into.
0コメント